Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
This is 100% Original Xhorse BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC.
UKOBD2 Provide top quality Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC, if you need Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC, or have any questions about Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC, welcome to contact us.
Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Porsche Piwis III, USB Link 2, Scania VCI3, CAN Clip, wiTech MicroPod 2, T300 key programmer, locksmith tools
images of Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC
100% Original Xhorse VVDI2 for BMW – Includes Basic + OBD + CAS4 + FEM/BDC Functions
Activated Software Features in VVDI2
- VB-01 BMW OBD
- VB-02 BMW CAS4
- VB-03 FEM/BDC Function
- VP-01 Porsche Immobilizer Data Tool
- VJ-01 Passthru J2534
- VK-01 Transponder Programmer
Comprehensive BMW Functions Supported by VVDI2
EEPROM, Kilometer, and Synchronization via OBD
- Read and Write EEPROM
- Read and Write KM
- Synchronize DME-CAS and CAS-ELV Systems
Key Programming and Management
- Get Key Information
- Write Key Information
- Load and Save Key Information
- Prepare Dealer Key Using Programmer
- Prepare Dealer Key via Ignition Switch
- Add New Key
- Program Key Information
- Repair Keyless Key
- Enable or Disable Key
- Clear DTC and Clear Shadow Memory
Key Creation from File
- EWS1, EWS2, EWS3, EWS4
- CAS1, CAS2, CAS3, CAS3+, CAS4
Key Unlocking Capabilities
- Unlock Using Key Info File
- Unlock Using CAS1/CAS2/CAS3/CAS3+ EEPROM Data
Kilometer Adjustment via File
- EWS3 and EWS4 Systems
- CAS1 to CAS4 Modules
- Cluster (E Series): M35080 EEPROM Dump
- Cluster (F Series)
CAS Module Repair Functions
- CAS1 (0K50E) OBDII Repair
- ISTAP4* Version OBDII Repair
VVDI2-BMW FEM/BDC System Support (Fully Released and Available)
Follow these steps for Key Programming: Get Key Info → Program FEM/BDC System → Make Key
- Supports creating new keys via ignition switch (add spare key or all keys lost; all key lost requires ISN)
- Allows resetting FEM/BDC kilometer data (cluster must be reset manually)
- Enables erasing stored keys (key position becomes blank after erase)
- Supports backup of module coding
- Supports restore of module coding
Important Notes for FEM/BDC Operations
- Backup and restore coding can typically be performed directly without additional steps.
- Adding keys, resetting KM, or erasing keys requires prior programming of the FEM/BDC system.
- If 'Get Key Info' shows an unsupported type, the message will appear: “Customer should use 'BMW E-sys software' to program FEM/BDC system,” then proceed with VVDI2-BMW programming.
- Do not close the software window during FEM/BDC system programming until all processes are complete.
- FEM/BDC programming involves soldering and EEPROM extraction. FEM uses a 95128 chip; BDC uses a 95256 chip. Two identical chips may be present—refer to the software diagram to select the correct one.
- After programming, always restore the original EEPROM data and coding. If issues arise after reinstallation (e.g., remote start failure or window malfunctions), use "BMW E-sys software" to recode the FEM/BDC system.
- If power is connected to the module but the relay continuously rings, contact technical support. Properly executed programming should result in smooth operation.
Package Contents
- VVDI2 Main Interface Unit
- 5th Generation BDM Programmer
- OBD2 Diagnostic Cable
- CAS Plus Module (additional component; must be purchased separately: CAS Plug for VVDI2 BMW or Full Version – 84.99 USD)
- Remote Key Programmer
- USB Connection Cable
Go to Buy: Xhorse VVDI2 BMW Version With Basic+BMW OBD+BMW CAS4+BMW FEM/BDC