bmw ews2 emulator

BMW EWS2 EWS3.2 emulator, it is an emulator for BMW E34 E36 E38 E39 E46.

Emulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free Shipping is a one of our bmw ews2 emulator Tools, you can buy Emulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free Shipping from ukobd2.com.

Wholesale Top quality VAS6154, GM Tech2, VCM II For Ford, Handy Baby II Car Key Chip Copier, CDP DS150

images of Emulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free Shipping

Emulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free ShippingEmulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free ShippingEmulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free Shipping

BMW EWS2 EWS3.2 Emulator for E34 E36 E38 E39 E46

Top 2 Reasons to Get the BMW EWS2 EWS3.2 Emulator

  1. There are NO counters or car start limits. You can change and store a new ISN without any limitations.
  2. The emulator is shipped with JUMPER 1 shorted. For testing purposes, ISN 0579 is stored by default.

Important Notice

In the case of EWS3.2, a similar procedure is used—the only difference is that it is NOT connected directly to the diagnostic K-line.

Connection Diagram

bmw-ews2-ews32-emulator-e34-e36-e38-e39-e46-2394-connection

BMW EWS Emulator Installation Instructions

  1. Remove the original EWS2 control unit. Locate the +12V ACC, GND, and K-line wires, then attach the emulator. Ensure the emulator is in service mode: JUMPER 1 must be shorted.
  2. Connect ANY K-line diagnostic adapter to the vehicle’s diagnostic connector and launch the EMULATOR CONFIGURATION UTILITY: bmw-ews-emulator-installation
  3. Choose the COM port, enter your desired ISN number, and press the Store button.
  4. For some ECUs, it is possible to read the ISN number directly from the engine control unit. In this case, select the option ECU xxxxx, then press Read. If successful, choose the option EWS emulator and press Store to save the ISN number into the emulator.
  5. Disconnect the emulator from the K-line, remove JUMPER 1, and connect the K output from the emulator to the DME(DDE) <-> EWS line.
  6. Don’t forget to short the two starter relay wires (EWS connector)!
  7. The car is now ready to start.

In the case of EWS3.2, a similar procedure is used—the only difference is that it is NOT connected directly to the diagnostic K-line.
There are NO counters or car start limits. You can change and store a new ISN without any limitations.
The emulator is shipped with JUMPER 1 shorted. For testing purposes, ISN 0579 is stored by default.

Package Includes

Go to Buy: Emulator E34 E36 E38 E39 E46 for BMW EWS2 EWS3.2 Best Selling Free Shipping

LONSDOR Key Programmer Porsche Piwis III GM Tech2 USB Link 2 CAN Clip wiTech MicroPod 2 T300 key programmer locksmith tools a b c d e f g h i j k l m n o p q r s t u v w x y z
Share to Pinterest